DS1678S/T&R【PDF 23/25 页】IC RECORDER REALTIME EVENT 8SOIC

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录1994

19页 20页 21页 22页 [23页]24页 25页

DS1678 Real-Time Event Recorder

7 of 25

DETAILED DESCRIPTION

The Event Counter Register contains the total number of events that have been logged in the current

event-logging mission. The Event Counter Register also allows the user to determine if the data in the

event-log memory has rolled over.

The 16-bit ETC can be incremented once per second, once per minute, or once per hour. Each event

transfers the current ETC value into the event-log memory, then clears and restarts the ETC. The three

increment periods allow users to maximize the resolution while providing an adequate maximum time

between events. The seconds resolution provides the time of an event down to the second, while allowing

up to 65,535 seconds (18.2 hours) between events without using additional event-log memory. The

minutes resolution provides the time of an event down to the minute, while allowing up to 45.5 days

between events without using extra memory locations. The hours resolution provides the time of an event

down to the hour in which it occurred, while allowing up to 7.5 years between events without using

additional event-log memory. Based on the expected frequency of events, an increment period can be

selected to maximize the resolution while minimizing use of the event-log memory.

The event can be triggered in three different ways depending on how the user programs the trigger select

(TRx) bits in the Control Register. The event can be triggered by a falling edge on the

INT pin only, a

rising edge only, or it can be triggered by rising and falling edges. Triggering with both the rising and

falling edges allows for monitoring when something is turned on/off and how long it is in either state.

The RTC provides seconds, minutes, hours, day, date, month, and year information with leap-year

compensation, and year 2000 compliance. The RTC also provides an alarm interrupt. The I2C interface

allows the RTC to function as a stand-alone RTC in the system.

The programmable alarm trip points in the RTC allow a flag to be set in the Control Register when the

specified time in the Alarm Trip Point Register is reached. The flag is readable via the I2C interface

during an event-logging mission or, when the DS1678 is not in a mission,

INT becomes an output and

generates an alarm interrupt if the value in the RTC equals the value in the RTC Alarm Register and the

duration interval select (DISx) bits are both set to zeros.

The DS1678 operates as a slave device on the I2C serial bus. Access is obtained by generating a START

condition and providing a device identification code. All data is transferred to and from the DS1678 most

significant bit (MSB) first. The address counter automatically increments so that subsequent registers can

be accessed sequentially until a STOP condition is executed. When VCC falls below 1.25 x VBAT, the

device automatically write protects itself by disabling the I2C interface, terminates any access in progress,

and resets the device address counter. Inputs to the device via the I2C bus are not recognized at this time

in order to prevent erroneous data from being written to the device from an out-of-tolerance system.

When VCC falls below VBAT, the device switches into a low-current battery-backup mode. Upon power-

up, the device switches from battery power to VCC when VCC is greater than VBAT + 0.2V, and recognizes

inputs from the system when VCC is greater than 1.25 x VBAT by releasing control of the write protection

on the I2C bus.

The Block Diagram shows the main elements of the RTC event recorder. The device has four major

components: a 64-bit RTC and control block, 32-byte user NV RAM, 2048 bytes of event-log memory

(1024 events), and an I2C serial interface.

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式